Can You Stuff Sausage With a Grinder?
Yes. Most meat grinders, including stand-mixer attachments, manual grinders and electric models, can be fitted with a stuffing tube. You remove the grinding knife and plate, add a stuffing plate or spacer if your model has one, and attach the tube. The auger then pushes already-ground, seasoned meat straight into the casing.
It’s a practical way to start making links without buying more equipment. The trade-off is that the auger works the meat a second time, which can warm it and smear the fat. With a cold mix and a little care, results can be very good for small batches.
What You Need
- A grinder with a stuffing tube kit for your specific model. Kits often include several tube diameters and sometimes a stuffing plate or “star” spacer.
- Seasoned sausage mix, already ground and mixed, and well chilled.
- Prepared casings. See our guide to sausage casings and how long to soak casings.
- A small bowl of water for wetting the tube and casing.
- A clean, damp work surface or tray to catch the sausage.
- A helper, if possible. Feeding and guiding at the same time is much easier with two people.
Which Grinder Plate to Use for the Grind
Grind first with the normal knife and plate, then switch to stuffing.
- 3/16 inch (about 4.5 mm): a common all-purpose plate for fresh sausage such as Italian, breakfast and bratwurst.
- 1/4 to 3/8 inch (about 6 to 10 mm): a coarse grind for rustic sausage, or as a first pass before a finer grind.
- 1/8 inch (about 3 mm): a fine grind for smoother sausage such as hot dogs or snack sticks, usually after a coarser first pass.
Setting Up the Grinder for Stuffing
Setups differ by brand, so check your manual. In general:
- Unplug the grinder and disassemble the head.
- Remove the knife and grinding plate. Some kits replace them with a stuffing plate or spacer so the auger sits correctly and the tube seats against it; others go straight from auger to tube.
- Choose a tube a bit narrower than your casing. For typical 32–35 mm hog casings, a tube with an outside diameter around 3/4 inch (about 19 mm) is common; narrower tubes are used for sheep casings.
- Attach the tube and tighten the locking ring firmly but without forcing it.
- Wet the tube or lightly grease it so the casing slides on.
Step by Step: Stuffing With a Grinder
- Chill the mix. It should be very cold going in, ideally below about 40°F (4°C). Our guide to how cold meat should be for grinding sausage has more detail.
- Load the casing. Gather a length of wet casing onto the tube like pushing up a sleeve, leaving a few inches hanging past the tip.
- Purge the air. Run the grinder on its lowest speed and feed a little mix until meat just reaches the tip of the tube. Then pull the casing end over it and tie a knot.
- Feed steadily. Drop small portions of mix into the hopper and press down gently with the pusher. Never use your fingers.
- Control the fill. Hold the casing lightly where it leaves the tube. More grip makes a tighter fill; less grip makes a looser one. Aim for firm but not tight, leaving room to twist links.
- Coil as you go. Let the sausage coil onto the work surface rather than hanging off the counter.
- Leave a tail. Stop with several inches of empty casing at the end so you can tie it off.
- Prick air pockets with a clean pin or sausage pricker.
- Link the coil by twisting. See how to twist and link sausages by hand.
Avoiding Fat Smear and Mushy Texture
Because the auger turns and compresses the meat, it can warm the fat and make the texture pasty. To limit this:
- Chill the mix thoroughly between mixing and stuffing, for example 30 minutes in the fridge or a shorter time in the freezer.
- Chill the grinder parts again before switching to stuffing.
- Work in small portions and return the rest of the mix to the fridge.
- Use the lowest speed your grinder offers.
- Don’t run the auger empty or let meat sit churning in the head.
If the sausage comes out looking greasy or smeared, stop and chill everything before continuing.
Dealing With the Meat Left in the Auger
When you finish, a fair amount of mix stays trapped around the auger and in the tube. You can push some through with a piece of bread or a few cubes of extra meat, then fry or freeze what’s left as patties. Cook a sample of any bread-pushed portion first, since it may include crumbs.
Grinder vs. Dedicated Stuffer
| Grinder with stuffing tube | Dedicated piston stuffer | |
|---|---|---|
| Up-front cost | Low if you already own a grinder | Additional purchase |
| Texture | Risk of fat smear from the auger | Pushes meat without reworking it |
| Control | Harder to control speed and fill | Smooth, steady, one-hand control |
| Waste | Meat left in auger | Little left in cylinder |
| Best for | Small, occasional batches | Regular or larger batches |
Many sausage makers start with a grinder and upgrade to a stuffer once they find they enjoy making links regularly.
Troubleshooting
- Casing keeps bursting: you may be overfilling or feeding too fast. See why sausage casings burst.
- Big air gaps: press the mix firmly into the hopper and feed continuously; prick any pockets afterward.
- Mix won’t feed: it may be too stiff or too cold and firm; let it soften slightly or add a splash of ice water during mixing.
- Texture is crumbly after cooking: the mix may not have been mixed long enough. See why homemade sausage is crumbly.
For the full process, see our beginner’s guide to making sausage at home.